Oberon’s CCOAPi-SKIN allows you to conceal the appearance of the popular Cisco 1040/1140/2600i/3500i/3600i series wireless access point. The skin is made from an RF transparent plastic, and can be attached directly to the Cisco 1040/1140/2600i/3500i/3600i. The CCOAPi-SKIN is paintable (do not use metalic paint) so it allows you to customize the color of the access point to partially conceal the access point or compliment interior color schemes.

Need to purchase now?

Oberon’s 1260/3500e-SKIN allows you to conceal the appearance of the popular Cisco 1260/3500e series wireless access point. The skin is made from an RF transparent plastic, and can be attached directly to the Cisco 1260/3500e. The 1260/3500e-SKIN is paintable so it allows you to customize the color of the access point to partially conceal the access point or compliment interior color schemes.

Surface mount modular receptacle to field terminate data caling within Oberon enclosures. Accepts Panduit Mini-Com® Modules for STP and UTP, fiber optic and audio/video, which snap in and out for easy moves, adds, and changes.

• Mounts easliy with adhesive tape or optional magnet (CMB-X)
• Cable entry from side and rear knockouts and from opening in center of base
• Includes built-in removable blank to add a second module
• Optional adhesive labels available
• Dimensions: .91"H x 1.77"W x 2.44"L

Cord Grip Connector Option Kit - For field termination. The Cord Grip Connector is mounted through a knockout hole in an enclosure for Ethernet cable pass-through. An unterminated Ethernet cable is pushed through the water tight, nylon connector providing strain relief as the connector is tightened on the Ethernet cable.

• Hand tightens - no tools needed for assembly
• Segmented chuck provides high mechanical pullout performance - will not cut or damage cord jacket
• Corrosion and weather resistant plastic is excellent for outdoor/indoor use
• UL listed

RJ-45 Bulkhead Pass-through Option Kit - For weather/dust proof terminations of data cable.

• RJ-45 Bulkhead Pass-through
• RJ-45 Cordsets available must specify length & termination (see Jumper Option Kit below)

Snap-In Bulkhead Connector Kit

• Plastic Snap-In Hole Connector
• 18" LMR195 RPSMA-F Bulkhead to RPSMA-M Pigtail
• Washers
• This RPSMA bulkhead connector snaps into the door of Oberon’s ceiling enclosures, permitting any dipole (“rubber duck”) antennas to be mounted on the door. Includes a plastic snap-in hole cover with RP-SMA(F) bulkhead connector, 18" LMR195 to RP-SMA(M) connector pigtail, and washers

Snap-In Bulkhead Connector Kit

• Plastic Snap-In Hole Connector
• 18" LMR195 RPTNC-F Bulkhead to RPTNC-M Pigtail
• Washers
• This RPTNC bulkhead connector snaps into the door of Oberon’s ceiling enclosures, permitting standard dipole (“rubber duck”) antennas to be mounted on the door. Includes a plastic snap-in hole cover with RP-TNC(F) bulkhead connector, 18" LMR195 to RP-TNC(M) connector pigtail, and washers

Jumper Option Kit (choice of jumper type) - Mates the Access Point to the Antenna

• 12" LMR195 Type N-(M) to Cisco Pigtail
  Part# 35-195NMRPTNCM-12
• 19" LMR100 Type N-(M) to Orinoco Pigtail
  Part# 35-100NMORI-19
• LMR400 and LMR600 cable types available

* Other jumpers are available
(Contact Customer Service)

Gore Vent Option Kit - Allows "breathing" for outdoor enclosures.

• 35-GOREVENT-KIT
• Outdoor environments for access point and enclosures can fluctuate drastically between night and day causing condesation to form on the inside of the enclosure. The 35-GOREVENT-KIT enables the enclosure to "breathe" allowing water vapor to exit the enclosure while preventing additonal water from enter it.

Lightning Arrestor Option Kit - comes with ring terminal

• 0-6 GHz Lightning Arrestor (N-Female)
  Part# 38-LA-NF
• 0-6 GHz Lightning Arrestor (Reverse Polarity TNC-Male)
  Part# 38-LA-RPTNCM

• This TYPE-N (F) to TYPE-N (F) Bulkhead adaptor can be inserted into knockouts and openings in Oberon’s ceiling and wall mounted enclosures to conveniently connect TYPE-N “jumpers” to the access point inside the enclosure, and attach dipole antennas to the exterior. Works with Oberon Model 1024-00.
  Part# ADP-NFBLKHD

• Designed to be installed in Oberon enclosures
• One input RJ45 connector and one output RJ45 connector
• A customer supplied CAT 5/6 jumper required between the PoE ILS output RJ45 connector and the wireless access point
• UL approved

• (1) PoE ILS PCB assembly
• Four (4) mounting screws
• Installation instructions

Optional Mounting Plate for use with the model 1052-00 ceiling enclosure.

4' x 10' White magnetic paper (Part No. 38-MAGNETCOVER) conceals mounting features for unused antennas on Oberon models 1053-00 and 1054-00.

Some ceiling systems use a 2' x 4' ceiling tile. With these larger ceiling tiles, use the 38-CEILING-TBAR to provide a clean installation of Oberon's 2' x 2' ceiling enclosures. This T-bar is a standard 15/16" inches wide

CADDY® SPEED LINK LD is a universal support system that quickly suspends static loads, even at an angle. It is a cost-effective alternate to jack chain, threaded rod and associated hardware in wireless enclosures, lighting, ductwork and other installation projects. The 1.5 mm (0.059 inch) wire rope with a crimped-on hook holds working loads of up to 20 kg (44 lb) with a 5:1 safety factor. Wire rope is 2 m (6.6 ft) long. TWO PER PACKAGE.

Installation Instructions

The CADDY Y-toggle is a universal support system that quickly suspends static loads, even at an angle. It is a cost-effective alternate to using jack chain, threaded rod and associated hardware to mount wireless access point enclosures, telecommunications enclosures, wire trays, etc. The toggles at the ends of the "Y" insert into mounting features in the back box of the ceiling enclosure, allowing quick mounting and leveling of enclosures. The Y-Toggle m eets the fire rating requirements of DIN 4102-2 for 30 minutes (for galvanized wire rope) and for 90 minutes (for stainless steel wire rope) at 30 percent of rated load, and w orks with a variety of CADDY® fasteners. The Y-toggle w orking load 44 lbs (20kg), and the Y-length is 19.6 in. (adjustable after installation).

Installation Instructions

The 36-SFCLT Seismic Fixture Clamps attach fixtures securely to the ceiling frame member. This set of reinforcing clamps is designed to prevent the T-bar from twisting and disconnecting at the T-Bar intersections in a seismic event. The reusable clamps also helps prevent the fixture from separating from the T-bar framework. They will withstand the force of a standard fire hose. The CADDY SFCLT family of fixture clamps consists of connectors for 2' x 4' and 2' x 2' light fixtures, as well as for end-to-end and side-by-side connections of light fixtures and for reinforcement of T-Bar main runner joints. In addition, they can be used to secure 2' x 2' air diffusers. Each reusable clamp is secured to the fixture and the T-Bar with two screws.Use of the clamps eliminates the need for two slack wires. The rated load of the CADDY SFCLT is 10 times the weight of a standard 30-lb light fixture. The clamp is designed to work together with T-Bar runners to provide seismic restraint for the fixture without additional chains or cables attached to the fixture itself.

Installation Instructions