|
Ceiling Enclosure - Multivendor AP & Antennas
|
Shown with optional
34-ZDUAL antennas
(not included)
|
Description
The Model 1052-00 wireless LAN access point enclosure is a locking 2' x 2' suspended ceiling tile enclosure for wireless access points and DAS remote units with detachable antennas. This aesthetic, white powder coated steel enclosure conveniently replaces a standard ceiling tile, and simplifies access point moves, adds, changes and maintenance. This model has openings in the door to mount up to seven external antennas. The 1052 series has interchangeable retrofit doors, allowing current owners to install new AP or antenna solutions from different vendors, simply by swapping doors.
Features
|
UL Listed
|
|
-
Accommodates most vendors enterprise access points and DAS Remotes with detachable antennas
-
Suitable for installation in the plenum space
-
Locking, fully hinged door, for mounting external antennas
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
2' x 2' suspended ceiling tile-like enclosure for most vendor’s wireless access points and DAS remote units. APs attach to internal universal T-Bar bracket
-
UL listed and designed to meet NEC 300-22 and 300-23 for plenum installations. OSHPD approved: OPA #1638-10 (.pdf)
-
Enclosure back box is effective dust barrier to simplify ICRA procedure compliance
-
This is a steel enclosure, so antennas MUST be mounted externally on the door. Accommodates up to (7) external antennas using the bulkhead connector kit for dipole antennas (Oberon P/N 35-BULKHD-KIT), Oberon 34-ZDUAL antennas, or other thru-hole ceiling mounted antennas with < 1" diameter stud
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Fully hinged locking door, keyed alike. Door can be replaced to migrate to new APs and antennas
-
Size: Flange is 23 ¾" x 23 ¾" ’, back-box is 12 ½" x 12 ½" x 4 ½" deep
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building structure, independent of the suspended ceiling
Model 1052-00 Includes:
Migrating to a new AP with an existing Model 1052 enclosure? Click here to view information on the on all of our Retrofit/Adapter Doors.
Videos
-
Migrating to the Cisco 1140/1260/3500/3600 series, Aruba AP105, or Enterasys 3610 wireless access point? Click here to view information on all of our retrofit doors.
-
Accessories
Mounting Plate:
Antennas:
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top |
| |
|
|
Locking Ceiling Mount - Cisco AP
|
Shown with
Cisco 3600i Access Point
(not included)
|
Description
The Model 1052-CCOAP wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically to conveniently mount and secure the Cisco 1040/1140/1260/3500/3600 series access points. The enclosure is based on Oberon’s popular 1052-00 universal wireless access point enclosure, with a door designed specifically for Cisco’s newest access points.
No ceiling tile cuts are required for installation. Just mount the access point into the door, place the ceiling tile enclosure in the ceiling, secure the enclosure to the ceiling support structure, and the access point is conveniently and aesthetically secured in the ceiling. Upgrades to different styles of access points are achieved by simply unlocking and replacing the door.
Features
|
|
UL Listed
|
|
-
Designed for securing Cisco enterprise access points with non-detachable antennas
-
Suitable for installation in air handling spaces
-
AP mounts in locking door
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Cisco 1040/1140/1260/3500/3600 series wireless access points
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be replaced to migrate to new access points.
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-CCOAP Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions view of the door, access point, access point mounting bracket, and assembly mount bracket
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Cisco AP & Antennas
|
Shown with
Cisco AIR-ANT2430V-R and
AIR-ANT5140V-R antennas
(not included)
|
Description
The Model 1052-CCOANT wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Cisco 1260, 3500e, and 3600e series wireless access point. This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Cisco 802.11n antennas, simplifying installation & optimizing wireless coverage. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing Cisco enterprise access points with detachable antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, for mounting Cisco MIMO antennas
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Cisco 1260, 3500e, and 3600e series APs
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Door mounting features for Cisco P/N AIR-ANT2430V-R and AIR-ANT5140V-R antennas only
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be replaced to migrate to new access points.
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-CCOANT Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions view of the door, access point, access point mounting bracket, and assembly mount bracket
Images
 
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Aruba Networks AP
|
Model 1052-DOME
|
Description
The Model 1052-DOME wireless LAN access point enclosure is a locking, 2' x 2' ceiling tile enclosure designed for Aruba Network’s, and other vendor’s, access points with non-detachable antennas (AP-100, AP-120, AP-130 series). This aesthetic, white powder coated steel enclosure has an impact resistant, RF transparent dome that extends only 4.5" below the ceiling plane. No ceiling tile cuts are required for installation. Access points attach to interior T-bar bracket.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks, and other, enterprise access points with external antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, with impact resistant plastic dome
-
Door is interchangeable with other Oberon 1050 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure designed for Aruba Network’s, and other vendor’s, access points with integrated, detachable, or non-detachable antennas (AP-100, AP-120, AP-130 series)
-
Access points attach to universal T-bar bracket on the interior
-
UL Listed and designed to meet NEC300-22 and 300-23 for plenum installations
-
-
Back-box is 16 ga. galvanized steel. Door and flange are textured white powder-coated steel
-
Dome is 9" dia. UL 94-5VA classified, impact resistant, RF transparent, textured white ABS plastic
-
Fully hinged locking door, keyed alike. Door can be replaced to migrate to new access points
-
Size: Flange is 2' x 2', back-box is 12.5" x 12.5" x 4.5" deep
-
Weight: 13lbs (not including access point or antenna)
-
De-rate upper operating temperature limit from +50°C to +40°C when AP in the enclosure
-
Ceiling enclosures must be supported by the building structure independent of the suspended ceiling
Model 1052-DOME Includes:
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Aruba Networks AP & Antennas
|
Shown with optional
AP-ANT-13B antennas
(not included)
|
Description
The Model 1052-AN wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically with mounting features for Aruba Networks access points with detachable antennas (AP-60, AP-70, AP-120, AP-124). This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Aruba Networks antennas, simplifying installation & optimizing wireless coverage. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks enterprise access points with detachable antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, for mounting antennas
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Aruba Networks APs with detachable antennas (AP-60, AP-70, AP-120, AP-124)
-
AP-70 requires Aruba Networks AP-70-MNT mounting bracket. AP-120 and AP-124 require the Aruba Networks AP-120-MNT mounting bracket. AP-60 requires the Aruba Networks AP-60-MNT mounting bracket (order from Aruba Networks)
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Mounting features on the door accommodate up to (3) Aruba Networks AP-ANT-13B antennas
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be swapped out to simplify migration to new access points or antennas
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
De-rate upper operating temperature limit from +50°C to +40°C when AP in the enclosure
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-AN Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
 
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Aruba Networks AP & Antennas
|
Shown with optional
AP-ANT-16 antenna
(not included)
|
Description
The Model 1052-AN-ANT16 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Aruba Networks access points with detachable antennas (AP-60, AP-70, AP-120, AP-124). This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Aruba Networks AP-ANT-16 antenna, simplifying installation & optimizing wireless coverage. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks enterprise access points with detachable antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, for mounting 3 X 1 antenna
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Aruba Networks access points with detachable antennas
-
AP-70 requires Aruba Networks AP-70-MNT mounting bracket. AP-120 and AP-124 require the Aruba Networks AP-120-MNT mounting bracket. AP-60 requires the Aruba Networks AP-60-MNT mounting bracket (order from Aruba Networks)
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Mounting features on the door for the Aruba Networks AP-ANT-16 802.11n, 3 element, dual band antenna
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
De-rate upper operating temperature limit from +50°C to +40°C when AP in the enclosure
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-AN-ANT16 Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
 
Accessories
Antennas:
- Dual Band, 3x1 MIMO antenna - 34-MIMO
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Aruba Networks AP
|
Shown with
Aruba Networks AP105
Access Point
(not included)
|
Description
The Model 1052-AP105 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically to conveniently mount and secure the Aruba Networks AP-105 wireless access points. The enclosure is based on Oberon’s popular 1052-00 universal wireless access point enclosure, with a door designed specifically for Aruba Networks AP105 wireless access point.
No ceiling tile cuts are required for installation. Just mount the access point into the door, place the ceiling tile enclosure in the ceiling, secure the enclosure to the ceiling support structure, and the access point is conveniently and aesthetically secured in the ceiling. Upgrades to different styles of access points are achieved by simply unlocking and replacing the door.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks AP105 enterprise access point
-
Suitable for installation in air handling spaces
-
AP mounts in locking door
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Suspended ceiling tile enclosure designed specifically for the Aruba Networks AP105 wireless access points
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be replaced to migrate to new access points.
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-AP105 Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions view of the door, access point, access point mounting bracket, and assembly mount bracket
Images
 
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Aruba Networks AP
|
Shown with
Aruba Networks AP135
Access Point
(not included)
|
Description
The Model 1052-AP135 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically to conveniently mount and secure the Aruba Networks AP-135 wireless access points. The enclosure is based on Oberon’s popular 1052-00 universal wireless access point enclosure, with a door designed specifically for Aruba Networks AP105 wireless access point.
No ceiling tile cuts are required for installation. Just mount the access point into the door, place the ceiling tile enclosure in the ceiling, secure the enclosure to the ceiling support structure, and the access point is conveniently and aesthetically secured in the ceiling. Upgrades to different styles of access points are achieved by simply unlocking and replacing the door.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks AP135 enterprise access point
-
Suitable for installation in air handling spaces
-
AP mounts in locking door
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Suspended ceiling tile enclosure designed specifically for the Aruba Networks AP135 wireless access points
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be replaced to migrate to new access points.
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-AP135 Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions view of the door, access point, access point mounting bracket, and assembly mount bracket
Images
 
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Enterasys AP
|
Shown with
Enterasys 3610 Access Point
(not included)
|
Description
The Model 1052-ENT3610 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically to conveniently mount and secure the Enterasys AP3605, AP3610, and AP3630 series wireless access points. The enclosure is based on Oberon’s popular 1052-00 universal wireless access point enclosure, with a door designed specifically for Enterasys’s newest access points.
No ceiling tile cuts are required for installation. Just mount the access point into the door, place the ceiling tile enclosure in the ceiling, secure the enclosure to the ceiling support structure, and the access point is conveniently and aesthetically secured in the ceiling. Upgrades to different styles of access points are achieved by simply unlocking and replacing the door.
Features
|
|
UL Listed
|
|
-
Designed for securing Enterasys enterprise access points with non-detachable antennas
-
Suitable for installation in air handling spaces
-
AP mounts in locking door
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Enterasys AP3605, AP3610 or AP3630 series access points
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Door mounting features for Cisco P/N AIR-ANT2430V-R and AIR-ANT5140V-R antennas only
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas. Door can be replaced to migrate to new access points.
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-ENT3610 Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions view of the door, access point, access point mounting bracket, and assembly mount bracket
Images
 
Accessories
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Enterasys AP & Antennas
|
Shown with
34-MIMO
Dual Band 802.11n antenna
(not included)
|
Description
The Model 1052-HFHS-N wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Enterasys HiPath 3620/3640 802.11n access point. This aesthetic, white powder coated steel enclosure has mounting features on the door for installation of an aesthetic dual band MIMO antenna. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing Enterasys and other enterprise access points with detachable antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door for mounting Oberon 3x1 MIMO antennas - P/N 34-MIMO
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Enterasys HiPath 3620/3640 access point
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Mounting features on the door for dual band 802.11n antenna (Enterasys P/N WS-AI-DT04360 dual band 802.11n MIMO antenna, 3 X 36” pigtails with RP-SMA connectors)
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1052-HFHS-N Includes:
-
Mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
 
Accessories
Antennas:
- Dual Band, 3x1 MIMO antenna - 34-MIMO
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Multivendor AP & Antennas
|
Shown with optional
34-ZDUAL antennas
(not included)
|
Description
The Model 1052-T wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Cisco 1232/1242/1260/3500e/3600e and many Aruba Networks access points. The enclosure accommodates many other manufacturers access points that have detachable antennas with Oberon’s optional universal mounting plate. This aesthetic, white powder coated steel enclosure has openings in the door for up to six antennas. The 1052-T features a 3/8” bevel in the flange around the perimeter, to match “tegular” ceiling tiles commonly used in new construction and renovations. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Accommodates most vendors enterprise access points and DAS Remotes with detachable antennas
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, for mounting antennas
-
Door is interchangeable with other Oberon 1052 series doors
-
Simplify code, industry directives, policy, and aesthetics compliance
-
" - T " indicates Tegular tile design, matches recessed grid ceiling tiles
Details
Specifications:
-
Suspended ceiling tile enclosure with integrated mounting features for Cisco 1242, Cisco 1260, Cisco 3500e, Cisco 3600e and Aruba Networks AP70 (requires Aruba AP-70-MNT mounting plate) and AP124 (requires Aruba AP-120-MNT mounting plate) access points
-
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Accommodates up to six antennas using the bulkhead connector kit for dipole antennas (Oberon part number:
35-BULKHD-KIT) or Oberon 34-ZDUAL or 34-DMDUAL antennas.
-
Fully hinged locking door, keyed alike. Door can be swapped out to simplify migration to new access points or antennas
-
Back-box is 16 ga. galvanized steel. Door and flange are textured, white powder-coated steel
-
Size: Tegular Flange is 24" x 24", AP Enclosure is 12½ " x 12½ " x 4½ "
-
Weight: 13lbs (not including access point or antenna)
Model 1052-T Includes:
-
Access point mounting screws
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Migrating to a new AP with an existing Model 1052 enclosure? Click here to view information on the on all of our Retrofit/Adapter Doors.
Accessories
Mounting Plate:
Antennas:
Security:
- Power over Ethernet Interlock Switch (PoE ILS) - Model 1790
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Cisco AP & Antennas
|
Shown with Cisco
AIR-ANT2430V-R and
AIR-ANT5140V-R antennas
(not included)
|
Description
The Model 1053-00 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Cisco 1250, 1260, 3500e, and 3600e series wireless access point. This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Cisco 802.11n antennas, simplifying installation & optimizing wireless coverage. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Cisco 1250, 1260, 3500e, and 3600e series APs. Use Cisco AIR-AP-BRACKET-2 for the Cisco 1260, 3500e, and 3600e wireless access points.
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Door mounting features for Cisco P/N AIR-ANT2430V-R and AIR-ANT5140V-R antennas only (not included)
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: Tegular Flange is 24" x 24", AP Enclosure is 13" x 13" x 5"
-
Weight: 15lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1053-00 Includes:
-
Snap lock mounting plate for the Cisco 1250 access point
-
Three light pipes to view access point LED’s externally
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Cisco AP & Antennas
|
Shown with
Cisco AIR-ANT2451NV-R
6 in 1 MIMO antenna
(not included)
|
Description
The Model 1053-01 wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically designed for Cisco 1250, 1260,3500e and 3600e series access point and antennas. Use Cisco AIR-AP-BRACKET-2 for the Cisco 1260, 3500e, and 3600e wireless access points. This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Cisco 802.11n antennas, simplifying installation & optimizing wireless coverage. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Cisco 1250, 1260, 3500e, and 3600e series APs and antennas. Use Cisco AIR-AP-BRACKET-2 for the Cisco 1260, 3500e, and 3600e wireless access points.
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Door designed to accommodate Cisco AIR-ANT2451NV-R 6 in 1 MIMO antenna (not included)
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: Tegular Flange is 24" x 24", AP Enclosure is 13" x 13" x 5"
-
Weight: 16lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1053-01 Includes:
-
Snap lock mounting plate for the Cisco 1250 access point
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Cisco AP & Antennas
|
Shown with Cisco
AIR-ANT2430V-R and
AIR-ANT5140V-R antennas
(not included)
|
Description
The Model 1053-T wireless LAN access point enclosure is a UL listed locking 2’ x 2’ ceiling tile enclosure designed specifically for the Cisco 1250, 1260, 3500e, and 3600e series wireless access points. This aesthetic, white powder coated steel enclosure has mounting features in the door for installation of the Cisco 802.11n antennas, simplifying installation & optimizing wireless coverage. The 1053-T features a 3/8” bevel in the flange around the perimeter, to match “tegular” ceiling tiles commonly used in new construction and renovations. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Ceiling tile enclosure specifically designed for Cisco 1250, 1260, 3500e, and 3600e series APs and antennas. Use Cisco AIR-AP-BRACKET-2 for the Cisco 1260, 3500e, and 3600e wireless access points.
-
Features a 3/8” bevel in the flange around the perimeter, to match "tegular" ceiling tiles. Designed for use with standard 15/16" width T-Bars, do not use with slim-line T-Bars.
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA 1638-10
(.pdf)
-
Door mounting features for Cisco P/N AIR-ANT2430V-R and AIR-ANT5140V-R antennas only (not included)
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: Tegular Flange is 24" x 24", AP Enclosure is 13" x 13" x 5"
-
Weight: 15lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1053-T Includes:
-
Snap lock mounting plate for the Cisco 1250 access point
-
Three light pipes to view access point LED’s externally
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Multivendor AP
|
 Model 1057-00
|
Description
Oberon’s Model 1057-00 suspended ceiling enclosure provides a secure, aesthetic, convenient mounting solution for wireless access points and DAS remote units from most vendors. The enclosure has a low profile, impact resistant ABS dome so that wireless access points with integrated or non-detachable antennas can be secured in otherwise unsecured spaces. The product is UL Listed and designed to satisfy National Electric Code (NEC) paragraphs 300-22 and 300-23 for installation in the air handling space. Locks are "keyed-alike" to simplify moves, adds, and changes.
Features
|
|
UL Listed
|
|
-
Designed for securing most vendors enterprise wireless access points and DAS Remotes
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, with impact resistant ABS dome
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
2' x 2' suspended ceiling tile wireless access point or DAS remote unit enclosure
-
Designed to accommodate wireless access points and DAS remote units from most vendors with integrated or non-detachable antennas
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Construction: 16 ga. galvanized steel back box, 18 ga. white powder coated flange, fully hinged locking door with UL 94-5VA ABS plastic dome
-
Dome is impact resistant and transparent to wireless signals
-
Knockouts for ¾” trade conduit connectors and snap-in keystone jacks and connectors
-
Size: Flange is 23 ¾" x 23 ¾', back box is 18.6" x 18.6" x 2.7", dome is 12" x 12" x 2". Total depth is 4.7"
-
Weight: 18.5 lbs (not including access point)
-
Enclosure must be supported by the building structure, independent of the suspended ceiling
Model 1057-00 Includes:
-
(1) Universal access point mounting plate
-
(1) cable egress fire block kit (½” trade size conduit connector, and fire block foam insert)
-
(2) Keys for lock
-
(4) Hanger wires
-
(4) # 6-32 x 3/8 Screws
-
(4) # 8-32 x 3/8 Screws
-
(4) # 10-32 x 3/8 Screws
-
(2) #4-40 machine nuts
-
Mounting Instructions
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Multivendor AP
|
 Model 1059-00
|
Description
The Model 1059-00 wireless LAN access point enclosure is a locking, 2’ x 2’ ceiling tile enclosure designed to accommodate access points with non-detachable antennas from most manufacturers. This aesthetic, white powder coated steel enclosure has an impact resistant, RF transparent door, which protrudes only 4" below the ceiling plane. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing most vendors enterprise wireless access points and DAS Remotes
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, with impact resistant plastic dome
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure designed for access points from most manufacturers
-
RF transparent cover allows use of access point with non-detachable or integrated antennas
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Dome is UL 94-5VA Classified ABS Plastic
-
Enclosure is deep enough for any access point with an overall height of less than 5¾ "
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, UL-94V5A impact resistant textured white ABS door
-
Size: Flange is 24" x 24", AP Enclosure is 18" x 18" x 2½ ", ABS dome is 14" sq. X 4" deep
-
Weight: 17½lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1059-00 Includes:
-
Universal mounting plate, mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Extreme Networks & Motorola AP & Antennas
|
|
|
Description
The Model 1059-MIMO wireless LAN access point enclosure is a locking, 2’ x 2’ ceiling tile enclosure designed for Extreme Networks Altitude 4620 Wireless Access Point (not included) This aesthetic, white powder coated steel enclosure has an impact resistant, RF transparent door, which protrudes only 4" below the ceiling plane. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing most vendors enterprise wireless access points and DAS Remotes with detachable antennas
-
Suitable for installation in air handling spaces
-
Antennas mount on locking door
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Ceiling tile enclosure designed for Extreme Networks Altitude 4620 Wireless Access Point (not included)
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Designed to be used with two dual band 802.11n antennas (P/N 34-S24493TS36RSM dual band 802.11n MIMO antenna)
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: Flange is 24" x 24", AP Enclosure is 18" x 18" x 2½ "
-
Weight: 17½lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1059-MIMO Includes:
-
Universal mounting plate, mounting screws and hardware
-
(4) Suspension wires
-
(2) ¾ " Trade conduit connectors for power and data cable openings in the back-box
-
Installation Instructions
Images
Accessories
Mounting Plate:
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Cisco AP
|
Shown with
Cisco 1131AG AP
(not included)
|
Description
The Model 1060-00 wireless access point ceiling mount is designed to provide a secure, convenient, and aesthetic mounting solution for the Cisco 1130 a/g access point. This aesthetic, white powder coated steel 2' x 2' ceiling tile-like mount locks the Cisco 1130a/g in place with a patented locking mechanism. Access point moves, adds, and changes can be performed without removing the mount from the ceiling. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Economical ceiling mount designed specifically for aesthetic, secure mounting of the Cisco 1130a/g access point
-
UL listed and designed to meet NEC300-22 and 300-23 for plenum installations
-
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Patented locking mechanism, keyed alike, secures AP into the ceiling mount
-
Size: 2' x 2' x 2¼" deep
-
Weight: 10 lbs (not including access point)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
-
Aesthetic, secure suspended ceiling tile mounting solution for the Cisco 1131AG AP wireless access point
Model 1060-00 Includes:
Images
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Cisco AP
|
Shown with
Cisco 1131AG AP
(not included)
|
Description
The Model 1060-T wireless access point ceiling mount is designed to provide a secure, convenient, and aesthetic mounting solution for the Cisco 1130 a/g access point. This aesthetic, white powder coated steel 2’ x 2’ ceiling tile-like mount locks the Cisco 1130a/g in place with a patented locking mechanism. Access point moves, adds, and changes can be performed without removing the mount from the ceiling. The 1060-T features a 3/8” bevel in the flange around the perimeter, to match “tegular” ceiling tiles commonly used in new construction and renovations. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Economical ceiling mount designed specifically for aesthetic, secure mounting of the Cisco 1130a/g access point
-
UL listed and designed to meet NEC300-22 and 300-23 for plenum installations (air handling space)
-
-
Features a 3/8” bevel in the flange around the perimeter, to match “tegular” ceiling tiles
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Patented locking mechanism, keyed alike, secures AP into the ceiling mount
-
Size: 2’ x 2’ x 2¼” deep
-
Weight: 10 lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1060-T Includes:
(1) ¾” Trade size conduit connector for data cable
(1) Fire block foam insert for conduit connector
(4) Hanger wires
Mounting Instructions
Images
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Cisco AP
|
Shown with
Cisco 1140AGN Series AP
(not included)
|
Description
The Model 1064-00 wireless access point ceiling mount is designed to provide a secure, convenient, and aesthetic mounting solution for the Cisco 1040/1140/1260/1600/3500/3600 series 802.11n access points. This aesthetic, white powder coated steel 2' x 2' ceiling tile-like mount locks the access point in place with a patented locking mechanism. Access point moves, adds, and changes can be performed without removing the mount from the ceiling. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Economical 2' x 2' suspended ceiling mount designed specifically for aesthetic, secure mounting of the Cisco 1040/1140/1260/1600/3500/3600 series access points
-
UL listed and designed to meet NEC300-22 and 300-23 for plenum installations, OSHPD approved ( OPA #1638) patent pending locking mechanism, keyed alike, secures Cisco AP into the ceiling mount
-
Enclosure back box is effective dust barrier to simplify ICRA procedure compliance
Details
Specifications:
-
Use Cisco AIR-AP-BRACKET-2 for ALL series Cisco APs. For installing Cisco 1040/1140/1260/1600 and 3500 series access points, use Oberon P/N 39-STANDOFF spacers so that AP fits properly in mount
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Size: 23 ¾" x 23 ¾" x 2" deep
-
Mount must be supported by the building structure independent of the suspended ceiling
Model 1064-00 Includes:
-
(1) cable egress fire block kit (½" trade size conduit connector, and fire block foam insert)
-
(2) keys for lock
-
(4) Hanger wires
-
Installation Instructions
-
Shipping Weight: 24lbs with 2 units per carton, 13lbs with 1 unit per carton
Images
Accessories
- P/N 39-STANDOFF: standoff which properly seat the Cisco 1040/1140/1260/1600 and 3500 series APs into the 1064-00
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Cisco AP
|
Shown with
Cisco 1140AGN Series AP
(not included)
|
Description
The Model 1064-T is identical to the 1064-00 except that it features a 3/8" bevel in the flange around the perimeter, to match "tegular" ceiling tiles commonly used in new construction and renovations. The tegular ceiling tiles are used in a ceiling system with a recessed grid. The 1064-T provides the best appearance in a recessed grid ceiling system.
Features
|
|
UL Listed
|
|
-
Economical 2' x 2' suspended ceiling mount designed specifically for aesthetic, secure mounting of the Cisco 1040/1140/1260/1600/3500/3600 series access points
-
UL listed and designed to meet NEC300-22 and 300-23 for plenum installations, OSHPD approved ( OPA #1638) patent pending locking mechanism, keyed alike, secures Cisco AP into the ceiling mount
-
Enclosure back box is effective dust barrier to simplify ICRA procedure compliance
Details
Specifications:
-
Use Cisco AIR-AP-BRACKET-2 for ALL series Cisco APs. For installing Cisco 1040/1140/1260/1600 and 3500 series access points, use Oberon P/N 39-STANDOFF spacers so that AP fits properly in mount
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Size: 23 ¾" x 23 ¾" x 2" deep
-
Mount must be supported by the building structure independent of the suspended ceiling
Model 1064-T Includes:
-
(1) cable egress fire block kit (½" trade size conduit connector, and fire block foam insert)
-
(2) keys for lock
-
(4) Hanger wires
-
Installation Instructions
-
Shipping Weight: 24lbs with 2 units per carton, 13lbs with 1 unit per carton
Images
Accessories
- P/N 39-STANDOFF: standoff which properly seat the Cisco 1040/1140/1260/1600 and 3500 series APs into the 1064-T
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Aruba Networks AP
|
Shown with
Aruba Networks AP135
(not included)
|
Description
The Model 1066-00 wireless access point ceiling mount is designed to provide a secure, convenient, and aesthetic mounting solution for the Aruba Networks AP-135 series 802.11n access points. This aesthetic, white powder coated steel 2' x 2' ceiling tile-like mount locks the access point in place with a patented locking mechanism. Access point moves, adds, and changes can be performed without removing the mount from the ceiling. No ceiling tile cuts are required for installation. The Model 1066-T features a 3/8" bevel in the flange around the perimeter, to match "tegular" ceiling tiles commonly used in new construction and renovations.
Features
|
|
UL Listed
|
|
-
Designed for securing Aruba Networks AP 135 enterprise wireless access points
-
Suitable for installation in air handling spaces
-
Patented locking mechanism secures AP
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Economical ceiling mount designed specifically for aesthetic, secure mounting of the Aruba Networks AP-135 series 802.11n wireless access points
-
UL listed and designed to meet NEC300-22 and 300-23 for plenum installations
-
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Patented locking mechanism, keyed alike, secures Access Point into the ceiling mount
-
Size: 2' x 2' x 2" deep
-
Weight: 10 lbs (not including access point)
-
Mount must be supported by the building structure independent of the suspended ceiling
Model 1066-00 Includes:
Images
|
| back to top
|
|
|
|
|
Locking Ceiling Mount - Multivendor AP & DAS Remote
|
Shown with Ruckus 7300
(not included)
|
Description
Oberon’s Model 1068-00 universal wireless access point ceiling mount is designed to provide a secure, convenient, and aesthetic mounting solution for most vendors' wireless access points and DAS remote access units. This aesthetic, white powder coated steel 2’ x 2’ ceiling tile-like mount locks the access point in place with a patent pending locking mechanism. The access point is attached to a vendor model specific mounting plate, and the plate is locked in place into the ceiling tile. Access point moves, adds, and changes can be performed without removing the mount from the ceiling. No ceiling tile cuts are required for installation.
Features
|
|
UL Listed
|
|
-
Designed for securing leading vendors enterprise wireless access points and DAS remotes
-
Suitable for installation in air handling spaces
-
Patent Pending locking mechanism secures AP
-
Interchangeable mounting plates permit simple migration to new vendors and technology
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Locking ceiling mount designed for secure, aesthetic, low profile mounting of most vendor’s wireless access points
-
Interchangeable mounting plates permit migration or upgrades to different vendor’s wireless solutions
-
UL Listed and designed to meet NEC paragraphs 300-22 and 300-23 for plenum installations
-
-
Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
-
Patent pending locking mechanism, keyed alike, secures access point into the ceiling mount
-
Size: 2' x 2' x 2" deep. Fits into standard (U.S.) suspended ceiling systems
-
Weight: 10.5 lbs (not including access point)
-
Mount must be supported by the building structure independent of the suspended ceiling, per NEC paragraph 300.11
-
Contact your Oberon representative for the vendor specific mounting plate required. Mounting plates are available for leading wireless access points. Mounting plates sold separately. See 'Accessories' tab
Model 1068-00 Includes:
Accessories
Oberon's model 1068-00 requires a specific mounting plate for each vendor’s access point solution.
- Cisco 1140, 1260, 3500, 3600 series access points:
- Order one Oberon P/N 68-CCOAP (Cisco AIR_BRACKET is not required)
- Aruba Networks AP-135 access point:
- Order one Oberon P/N 68-AP135 (Aruba Networks wall mount bracket is not required)
- Ruckus AP7300 series access point:
- Order one Oberon P/N 68-R7300 (no additional mounting bracket required)
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Clear PC Dome for Multimedia Gateway
|
Shown with
Apple TV
(not included)
|
Description
The Model 1075-CP multi-media ceiling enclosure is designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1075-CP has a clear polycarbonate dome to enable the wireless and IR remote control functions of the Apple TV media gateway and similar products. Once installed, this ceiling enclosure permits controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder coated steel enclosure fits into a cutout in the ceiling tile, and include tile bridges to support the enclosure in the ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
15" x 15" Ceiling tile insert telecommunications enclosure designed for securing most manufacturer’s multimedia gateways, such as the Apple TV, and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Multimedia Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
UL Listed, designed to meet NEC 300-22 and 300-23 for plenum installations
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured white, powder coated steel door; textured white, powder coated steel flange; UL Classified domes
-
Fully hinged locking door, keyed alike
-
Size: flange is 15" x 15", back box is 12 ¾" x 12 ¾" x 3" deep
-
Weight: 6.5 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not the tile gridwork
Model 1075-CP Includes:
|
| back to top |
| |
|
|
Ceiling Enclosure - White ABS Dome for Multi-vendor WAP
|
|
|
Description
The Model 1075-WA multi-media ceiling enclosure is designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1075-WA has a white ABS dome to enable the wireless and IR remote control functions of the Apple TV media gateway and similar products. Once installed, this ceiling enclosure permits controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder coated steel enclosure fits into a cutout in the ceiling tile, and include tile bridges to support the enclosure in the ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
15" x 15" Ceiling tile insert telecommunications enclosure designed for securing most manufacturer’s multimedia gateways, such as the Apple TV, and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Multimedia Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
UL Listed, designed to meet NEC 300-22 and 300-23 for plenum installations
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured white, powder coated steel door; textured white, powder coated steel flange; UL Classified domes
-
Fully hinged locking door, keyed alike
-
Size: flange is 15" x 15", back box is 12 ¾" x 12 ¾" x 3" deep
-
Weight: 6.5 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not the tile gridwork
Model 1075-WA Includes:
|
| back to top |
| |
|
|
Ceiling Enclosure - Cisco AP
|
Shown with Cisco
3500i wireless access point
(not included)
|
Description
The Model 1075-CCOAP wireless LAN access point mounting solution is a locking ceiling tile insert designed specifically to secure the Cisco 1040/1140/1260/3500/3600 series access points while satisfying UL2043 criteria for heat and visible smoke release in air-handling spaces. This aesthetic, white powder-coated all steel enclosure has a bracket in the door to which the access point is attached. When the door is closed, the access point is locked in place and the enclosure preserves the UL2043 criteria. Installation requires a square opening to be cut into the ceiling tile or hard ceiling. The enclosure is supported by two backside tile bridges, and supporting grid wires attached to the structural ceiling support.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Ceiling tile insert designed specifically for the Cisco 1040/1140/1260/3500/3600 series wireless APs
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Meets UL 2043 Fire Test for heat and visible smoke release in air handling spaces; Intertek report #3121942SAT-002
-
Access point attaches directly to door. Standard Cisco dipole antennas protrude through the door. No other antenna options are available with this model
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: flange is 15" x 15", back box is 12 ¾" x 12 ¾" x 3" deep
-
Weight: 11lbs (not including access point or antenna)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1075-CCOAP Includes:
-
Mounting screws & hardware
-
(4) Suspension wires, and (2) tile bridges
-
½" and 1" (trade-size) cable openings for power and data cable in the back-box
-
½" Conduit nipple
-
Installation Instructions
|
| back to top
|
|
|
|
|
Ceiling Enclosure - Aruba Networks AP
|
Shown with
Aruba Networks AP135
(not included)
|
Description
The Model 1075-AP135 wireless LAN access point mounting solution is a locking ceiling tile insert designed specifically to secure the Aruba Networks AP134/135. This aesthetic, white powder-coated enclosure has a bracket in the door to which the access point attaches to. When the door is closed, the access point is locked in place. Installation requires a square opening to be cut into the ceiling tile or hard ceiling. The enclosure is supported by two backside tile bridges, and supporting grid wires attached to the structural ceiling support. The door is interchangeable for new doors specific to different manufacturer’s access points and antennas.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
Ceiling tile insert designed to be used with any style and size of ceiling tile
-
Designed specifically to conveniently mount and secure the Aruba Networks AP130 series access points
-
UL Listed and designed to meet NEC300-22 and 300-23 for plenum installations
-
OSHPD approved, OPA #1638-10
-
Construction: 18 gauge, textured white powder coated aluminum
-
Fully hinged locking door, keyed alike
-
Size: Flange is 15" x 15", enclosure is 12.5" x 12.5" x 3" deep, 3.25" useful depth with universal mounting plate in place. Weight: 7 lbs
-
Weight: 6.5 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not tile gridwork
Model 1075-AP135 Includes:
|
| back to top |
| |
|
|
Ceiling Enclosure - Clear PC Dome for Multimedia Gateway
|
 Shown with
Cisco 3500 AP
(not included)
|
Description
The Model 1077-CP series multi-media ceiling enclosures are designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1077-CP has a clear polycarbonate dome to enable the wireless and IR remote control functions of the Apple TV media gateway and similar products. Once installed, these ceiling enclosures permit controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder coated steel enclosure fits into a 2' x 2' suspended ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
2’ x 2’ Ceiling tile telecommunications enclosure designed for ceiling mounting most manufacturer’s multimedia gateways and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
Designed to meet NEC300-22 and 300-23 for plenum installations
-
OSHPD approved OPA #1638(up to 25lbs. total weight)
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured white, powder coated steel door; textured white, powder coated steel flange
-
Fully hinged locking door, keyed alike
-
Knockouts for AC receptacle, (2) keystone jacks, (2) ¾" trade conduit connector
-
Size: flange is 23 ¾" x 23 ¾", back box is 12 ¾"x 12 ¾" x 3" deep
-
Weight: 11 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not the tile gridwork
Model 1077-CP Includes:
-
(4) Ceiling support wires
-
(1) cable egress fire block kit (½" trade size conduit connector, and fire block foam insert)
-
Mounting Instructions
|
| back to top |
| |
|
|
Ceiling Enclosure - White ABS Dome for Multi-vendor WAP
|
 Model 1077-WA
|
Description
The Model 1077-00 series multi-media ceiling enclosures are designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1077-CP has a clear polycarbonate dome to enable the wireless and IR remote control functions of the Apple TV® media gateway and similar products. Once installed, these ceiling enclosures permit controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder-coated steel enclosure fits into a 2' x 2' suspended ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
2' x 2' Ceiling tile telecommunications enclosure designed for ceiling mounting most manufacturer’s multimedia gateways and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
UL Listed and designed to meet National Electric Code paragraphs 300-22 and 300-23 for use in the above ceiling space
-
OSHPD approved OPA #1638(up to 25lbs. total weight)
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured, white powder-coated steel door; textured, white powder-coated steel flange
-
Fully-hinged locking door, keyed alike
-
Knockouts for AC receptacle, (2) keystone jacks, (2) ¾" trade conduit connector
-
Size: Flange is 23 ¾" x 23 ¾", back-box is 12 ¾" x 12 ¾" x 3" deep
-
Maximum weight to be installed in the unit is 25 lbs.
-
Enclosure must be supported by the building structural system, not the ceiling tile gridwork
Model 1077-WA Includes:
Documents
Images
|
| back to top |
| |
|
|
Multi-media Gateway and Access Point Ceiling Enclosure
|
Shown with
Cisco 3600i Access Point
(not included)
|
Description
The Model 1077-00 series multi-media ceiling enclosures are designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1077-CP has a clear polycarbonate dome to enable the wireless and IR remote control functions of the Apple TV media gateway and similar products. Once installed, these ceiling enclosures permit controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder coated steel enclosure fits into a 2' x 2' suspended ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
2’ x 2’ Ceiling tile telecommunications enclosure designed for ceiling mounting most manufacturer’s multimedia gateways and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
Designed to meet NEC300-22 and 300-23 for plenum installations
-
OSHPD approved OPA #1638(up to 25lbs. total weight)
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured white, powder coated steel door; textured white, powder coated steel flange
-
Fully hinged locking door, keyed alike
-
Knockouts for AC receptacle, (2) keystone jacks, (2) ¾" trade conduit connector
-
Size: flange is 23 ¾" x 23 ¾", back box is 12 ¾"x 12 ¾" x 3" deep
-
Weight: 11 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not the tile gridwork
Model 1077-CCOAP Includes:
-
(4) Ceiling support wires
-
(1) cable egress fire block kit (½" trade size conduit connector, and fire block foam insert)
-
Mounting Instructions
|
| back to top |
| |
|
|
Multi-media Gateway and Access Point Ceiling Enclosures
|
Shown with
Aruba Networks AP135
Access Point
(not included)
|
Description
The Model 1077-00 series multi-media ceiling enclosures are designed to provide a convenient way to mount and secure digital media gateways, wireless access points and other components in the ceiling. The 1077-CP has a clear polycarbonate dome to enable the wireless and IR remote control functions of the Apple TV media gateway and similar products. Once installed, these ceiling enclosures permit controlled access to components without lifting ceiling tiles. Interchangeable retrofit doors permit vendor and technology migrations, again, without lifting ceiling tiles. This aesthetic, aluminum and white powder coated steel enclosure fits into a 2' x 2' suspended ceiling.
Features
|
|
UL Listed
|
|
-
Simplifies compliance with industry standards and guidelines for Retail (PCI), Healthcare (ICRA), and Goverment deployments
-
Secure, Convenient, Aesthetic
Details
Specifications:
-
2’ x 2’ Ceiling tile telecommunications enclosure designed for ceiling mounting most manufacturer’s multimedia gateways and wireless access points
-
Interchangeable doors permit simple customization and migration to vendor unique products
-
Gateways attach to clear plastic insert, access points attach to T-bar within enclosure
-
Designed to meet NEC300-22 and 300-23 for plenum installations
-
OSHPD approved OPA #1638(up to 25lbs. total weight)
-
Construction: 16 ga. clear coat aluminum back-box; 14 ga. textured white, powder coated steel door; textured white, powder coated steel flange
-
Fully hinged locking door, keyed alike
-
Knockouts for AC receptacle, (2) keystone jacks, (2) ¾" trade conduit connector
-
Size: flange is 23 ¾" x 23 ¾", back box is 12 ¾"x 12 ¾" x 3" deep
-
Weight: 11 lbs (not including internal equipment)
-
Enclosure must be supported by the building ceiling structural system, not the tile gridwork
Model 1077-AP135 Includes:
-
(4) Ceiling support wires
-
(1) cable egress fire block kit (½" trade size conduit connector, and fire block foam insert)
-
Mounting Instructions
Images
 
|
| back to top |
| |
|
Model 1030-FLANGE & Model 1030-00 Ceiling Enclosure - Multivendor AP
|
Shown with Oberon
Model 1030-00 enclosure
(sold separately)
|
Description
Oberon's Model 1030-00 "hard lid" or wall mount enclosure provides a secure, aesthetic, convenient mounting solution for wireless access points from most vendors. The enclosure has a low profile impact resistant ABS dome so that wireless access points with integrated or non-detachable antennas can be secured in otherwise unsecured spaces. The product is UL Listed and designed to satisfy National Electric Code (NEC) paragraphs 300-22 and 300-23 for installation in the air handling space. Locks are "keyed-alike" to simplify moves, adds, and changes. An optional suspended ceiling flange kit, 1030-FLANGE, permits the Model 1030-00 to be mounted in a standard 2' x 2' suspended ceiling system.
Features
|
|
UL Listed
|
|
-
Designed for securing most vendors enterprise wireless access points and DAS Remotes
-
Suitable for installation in air handling spaces
-
Locking, fully hinged door, with impact resistant plastic dome
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications: (Model 1030-00 and 1030-FLANGE combined)
-
Wireless access point enclosure designed to be surface mounted on "hard-lid" ceilings or walls
-
Designed to accommodate wireless access points from most vendors with integrated or non-detachable antennas
-
UL listed and designed to meet NEC300-22 and 300-23 for installations in the air handling space, OSHPD approved OPA #1638-10
(.pdf)
-
Construction: 16 gauge, powder coated steel back box, fully hinged locking door with UL 94-5VA ABS plastic
-
Dome is impact resistant and transparent to wireless signals
-
Knockouts for ¾" trade conduit connectors and snap-in keystone jacks and connectors
-
Opening in back box for wall jacks
-
Size: Flange is 24" x 24", back box is 17" x 17" x 1.7", the dome is 12" x 12" x 2". Total depth is 3.7"
-
Weight: 1030-00 plus 1030-FLANGE kit is 17.5 lbs (not including access point)
-
Suspended ceiling flange kit (part number 1030-FLANGE) is optional. This is a special purchase item, minimum purchase may apply. Please contact your Oberon representative for availability
-
If enclosure is in ceiling, it must be supported by the building ceiling structural system, not tile gridwork
Model 1030-FLANGE & 1030-00 Includes:
Images
 
Accessories
Mounting Plate:
|
| back to top
|
|
|
|
|
Above Ceiling Hanger
|
Shown with
Cisco 1142 Access Point
(not included)
|
Description
Oberon's 1045-00 is a sturdy, above ceiling hanger bar designed to support wireless access points and DAS remote units from most leading vendors. Wireless equipment should not be placed on top of ceiling tiles, and antennas should not poke through ceiling tiles. Conventional box hangers are not sturdy enough to reliably support wireless equipment in the preferred orientation. Use the access point equipment vendor’s standard ceiling grid clip to clip the equipment to the 1045s T-bar universal mounting bracket. Antennas can be mounted to the antenna mounting plate. Hanger bar extensions allow the hanger bar to be raised 2.5" for larger items. A support wire is included to ensure compliance with the National Electric Code (NEC®) Section 300-11, which requires an independent support.
Features
-
Designed for securing most vendors enterprise wireless access points and DAS Remotes
-
Suitable for installation in air handling spaces
-
Simplify code, industry directives, policy, and aesthetics compliance
Details
Specifications:
-
Sturdy above suspended ceiling hanger bar designed for wireless access points, DAS remote units, and associated antennas antennas
-
Equipment should be supported by the building structure, independent of the suspended ceiling
Model 1045-00 Includes:
-
(1) Heavy duty hanger bar
-
(2) Hanger bar extensions
-
(1) 3m wire rope for independent support
-
(1) Universal wireless equipment "T-Bar" mounting bracket
-
(1) Antenna Mounting plate
-
(1) Installation Instructions
Images
 
|
| back to top
|
|
|
|
Spec Sheet
