These enclosures are designed to permit convenient and secure mounting of the access point on walls or in rooms with a hard “lid” or ceiling. The enclosures include a universal mounting plate for access points from many vendors, “keyed alike” locks, and knockouts for antennas, which can either protrude through the enclosure or can be installed as bulkhead kits. The enclosures are designed to the UL50 standard for enclosure integrity and carry an OPA number.
| Model 1029-00 |
|
-
Right angle wireless access point mount designed for attaching to indoor walls, where secure horizontal mounting is required
-
Designed for Cisco 1140/1260/3500/3600 series and Aruba Networks AP105 access points
-
Knockouts on two sides and top for ½” trade size conduit clamps
-
2 Part Construction: 18 ga. textured white powder-coated steel right angle bracket and cover
-
Size: 9" x 6" x 5"
-
Weight: 2½ lbs (not including access point)
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1030-00 |
|
-
Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls
-
May be mounted in suspended ceiling using optional suspended ceiling flange kit (Part No. 1030-FLANGE)
-
Designed to accommodate wireless access points with integrated or non-detachable antennas (reference enclosure selection guide)
-
OSHPD approved (OPA #1638)
-
Designed to meet NEC300-22 and 300-23 for installations in the air handling space
-
Fully hinged locking door, keyed alike
-
Construction: 16 ga. textured white powder-coated steel, and impact resistant UL 94-5VA classified RF transparent dome
-
Size: 17" x 17" x 3¾" (total depth), the dome is 13" x 13" x 2"
-
Weight: 6 lbs (not including access point)
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1032-00 |
|
-
Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls (NOTE: When using the Aruba Networks AP105 please use the AP-105-MNT to mount the AP; When using the Aruba Networks AP135 please use the AP-135-MNT; When using Cisco APs w/ integrated antennas please use the Aironet AIR-AP-BRACKET-1 to mount the AP)
-
Economical solution for securing smaller wireless access points with integrated or non-detachable antennas (reference enclosure selection guide)
-
Cover is UL listed (UL 94-5VA)
-
Fully hinged locking door, keyed alike
-
Construction: 16 ga. textured white powder-coated steel, and impact resistant UL 94-5VA classified RF transparent dome
-
Size: 11" x 11" x 34.4" (total depth)
-
Weight: 4.5 lbs (not including access point)
-
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1032-C |
|
-
Virtually identical to the Model 1032-00 but with a clear ABS cover, this wireless access point enclosure is designed to be surface mounted on “hard-lid” ceilings or walls (NOTE: When using the Aruba Networks AP105 please use the AP-105-MNT to mount the AP; When using the Aruba Networks AP135 please use the AP-135-MNT; When using Cisco APs w/ integrated antennas please use the Aironet AIR-AP-BRACKET-1 to mount the AP)
-
Economical solution for securing smaller wireless access points with integrated or non-detachable antennas (reference enclosure selection guide)
-
Cover is see-through and UL listed
-
Fully hinged locking door, keyed alike
-
Construction: 16 ga. textured white powder-coated steel, and impact resistant UL 94-5VA classified RF transparent dome
-
Size: 11" x 11" x 34.4" (total depth)
-
Weight: 4.5 lbs (not including access point)
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1021-00 |
|
|
-
Ideal for stadium installations. Oberon’s NEMA enclosures are an excellent match for Cisco 3502p wireless access point and MIMO Patch Antenna Array stadium antenna
-
Designed for mounting wireless access points with non-detachable antennas indoors or outdoors where secure weather proof installation is required
-
Fully hinged door wit lock clasp. Door has a neoprene perimeter gasket
-
Construction: ABS plactic, grey, paint-able; NEMA-4 capable when openings are properly sealed; Virtually transparent to RF signal
-
UL listed and tested to UL508-4X requirements
-
Typical temperature rise is less than 10°C with powered access point (to avoid excessive heat build-up in the enclosure, avoid direct exposure to sunlight)
-
Size: 12" x 10" x 6" deep
-
Weight: 4 lbs
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1025-00 |
|
|
-
Designed for mounting wireless access points with non-detachable antennas indoors or outdoors where secure weather proof installation is required
-
Large enough for Cisco 1250 802.11n wireless access point with 6 internal dipole antennas
-
Use Cisco AIR-AP-BRACKET-2 when mounting Cisco 1040, 1140, 1250, 1260, 3500, and 3600 series wireless access points
-
(2) ¾ trade size cable feed-through openings in the bottom
-
Fully hinged locking door, weather-proof lock. Door has a neoprene perimeter gasket
-
Construction: 30% fiberglass reinforced polyester, grey, paint-able; NEMA-4 capable when openings are properly sealed; Virtually transparent to RF signal
-
UL listed and tested to UL508-4X requirements
-
Typical temperature rise is less than 10°C with powered access point (to avoid excessive heat build-up in the enclosure, avoid direct exposure to sunlight)
-
Size: 13" x 15" x 6.5" deep
-
Weight: 10½lbs
-
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1026-00 |
|
|
-
Ideal for stadium installations. Oberon’s NEMA enclosures are an excellent match for Cisco 3502p wireless access point and MIMO Patch Antenna Array stadium antenna
-
Designed for mounting wireless access points with non-detachable antennas indoors or outdoors where secure weather proof installation is required
-
Fully hinged door wit lock clasp. Door has a neoprene perimeter gasket
-
Construction: ABS plactic, grey, paint-able; NEMA-4 capable when openings are properly sealed; Virtually transparent to RF signal
-
UL listed and tested to UL508-4X requirements
-
Typical temperature rise is less than 10°C with powered access point (to avoid excessive heat build-up in the enclosure, avoid direct exposure to sunlight)
-
Size: 12" x 10" x 6" deep
-
Weight: 6 lbs
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1022-00 |
|
-
Designed for surface mounting on indoor hard walls, where secure mounting is required
-
Large enough for the Cisco 1250 Access Point with 6 antennas
-
Internal mounting plate accomodates APs from most vendors
-
Antennas may be mounted externally using optional bulkhead connectors (Oberon Part Number: 35-BULKHD-KIT)
-
Beveled corners permit easy installation in the corner of the room
-
-
Fully hinged locking door, keyed alike
-
Construction: 18 ga. textured white powder-coated steel
-
Size: 11" x 12 ½" x 5 ¼", 3 ¾" useful depth with universal mounting plate in place
-
Weight: < 7lbs
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1023-00 |
|
|
-
Designed for surface mounting on indoor hard walls, where secure mounting is required
-
Internal mounting plate accomodates APs from most vendors
-
Cisco 1242 dipole antennas protrude through knockouts
-
Antennas may be mounted externally using optional bulkhead connectors (Oberon Part Number: 35-BULKHD-KIT)
-
Beveled corners permit easy installation in the corner of the room
-
-
Fully hinged locking door, keyed alike
-
Construction: 18 ga. textured white powder-coated steel
-
Size: 7 ¾" x 11" x 3 ½", 3" useful depth with universal mounting plate in place
-
Weight: < 6lbs
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
| Model 1027-00 |
Shown with optional antennas
and bulkhead connector kit.
(Not included) |
-
Aesthetic access point enclosure designed to be recess mounted in hard lid ceilings or walls. Accom-modates 1 Access Point from most manufacturers (reference enclosure selection guide)
-
UL listed and Designed to meet NEC300-22 and 300-23 for installations in the air handling space
-
Up to four antennas can be mounted on the door using the bulkhead connector kit (Oberon part number: 35-BULKHD-KIT) or Oberon 34-ZDUAL antennas.
-
Mounting holes located 16" on center
-
Fully hinged locking door, keyed alike
-
Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
-
Size: 17½" x 17½" flange, 12½" x 12½" x4½" backbox
-
Weight: 11lbs (not including access point or antenna)
|
Enclosure PDFs: |
Spec Sheet | Installation Instructions | Customer Prints |
| back to top |
| |
|
RSS
